Your Shopping cart is empty.

Ohitus pääsisältöön »

Moottoriohjaimet

7 tuote(tta)

/ sivu

Listana  Taulukkona 

Laskeva
  1. Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit - v2.3

    Adafruit Motor/Stepper/Servo Shield for Arduino v2 Kit - v2.3

    23,00 €

    Adafruit motor shield for running DC, stepper and servo motors.

    Lue lisää...
  2. Pololu DRV8834 Stepper Motor Driver – Low-Voltage

    Pololu DRV8834 Stepper Motor Driver – Low-Voltage

    6,90 €

    This is a breakout board for TI’s DRV8834 microstepping bipolar stepper motor driver. It has a pinout and interface that are nearly identical to those of our A4988 carriers, so it can be used as a drop-in replacement for those boards in many applications. The DRV8834 operates from 2.5–10.8 V, allowing stepper motors to be powered with voltages that are too low for other drivers, and can deliver up to approximately 1.5 A per phase continuously without a heat sink or forced air flow (up to 2 A peak). It features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). This board ships with 0.1″ male header pins included but not soldered in.

    Lue lisää...
  3. Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi

    Pololu DRV8835 Dual Motor Driver Kit for Raspberry Pi

    9,00 €

    ‌This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+, Pi A+, Pi 2, or Pi 3 and provides an easy and low-cost solution for driving a pair of small brushed DC motors.

    Lue lisää...
  4. Pololu A4988 Stepper Motor Driver - Green

    Pololu A4988 Stepper Motor Driver - Green

    6,90 €

    This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling). This board ships with 0.1″ male header pins included but not soldered in.

    Lue lisää...
  5. Pololu A4988 Stepper Motor Driver - Black Edition

    Pololu A4988 Stepper Motor Driver - Black Edition

    8,90 €

    The A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than our two-layer (green) version. Like the original carrier, the Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. This board ships with 0.1″ male header pins included but not soldered in.

    Lue lisää...
  6. Pololu DRV8824 Stepper Motor Driver - Low Current

    Pololu DRV8824 Stepper Motor Driver - Low Current

    8,90 €

    This is a breakout board for TI’s DRV8824 microstepping bipolar stepper motor driver, a lower-current version of the DRV8825. It can deliver up to 0.75 A per coil without a heat sink (it is rated for up to 1.2 A per coil with sufficient additional cooling), and it has larger current-sense resistors than the DRV8825 that allow for improved microstepping performance at low currents. This carrier has the same pinout, interface, and features as our DRV8825 carrier, which means it can serve as a direct substitute for the DRV8825 carrier when using lower-current stepper motors. This board ships with 0.1″ male header pins included but not soldered in.

    Lue lisää...
  7. Pololu DRV8825 Stepper Motor Driver - High Current

    Pololu DRV8825 Stepper Motor Driver - High Current

    9,90 €

    Loppu varastosta

    This breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). The driver has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. This board ships with 0.1″ male header pins included but not soldered in.

    Lue lisää...

7 tuote(tta)

/ sivu

Listana  Taulukkona 

Laskeva