0Item(s)

Ostoskorissasi ei ole yhtään tuotetta.

Product was successfully added to your shopping cart.

Tarvikkeet

Laskeva

   

16 tuote(tta)

  1. DS3231 Precision RTC FeatherWing - RTC Add-on For Feather Boards

    ‌This is the DS3231 Precision RTC FeatherWing: it adds an extremely accurate I2C-integrated Real Time Clock (RTC) with a Temperature Compensated Crystal Oscillator (TCXO)  to any Feather main board.

    15,00 €
  2. SparkFun FT231X Breakout

    ‌The 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications.

    14,00 €
  3. Arduino Stackable Header Kit - R3

    These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (1 8-pin, 1 10-pin and 2 6-pin), enough to connect a shield to an Arduino board. These are the same headers we use in our tutorials and with our own shields.

  4. LilyPad Protoboard Small

    This is a small board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1" array. Check rear photo for trace configuration.

  5. Conductive Thread Bobbin - 18 m

    This is 60 feet (18 m) of conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of thread. 60 feet of thread is enough to get a simple design stitched onto your shirt, backpack or hat.

    3,50 €
  6. LilyPad Accelerometer ADXL335

    This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration.

    15,00 €
  7. LilyPad Buzzer

    This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a pocket but not obtrusively loud.

  8. Conductive Fabric - 12"x13" Ripstop

    This is a conductive knit fabric for use in e-textiles. It is similar in feel to a nylon ripstop material. It is highly conductive with a surface resistivity of < 1 ohm/sq. This is a great add-on to any LilyPad project.

    10,00 €
  9. LilyPad LiPower

    A small, but very mighty power supply. This board was designed to be as small and inconspicuous as possible. The nice thing about LiPower is the ability to use rechargable Lithium Polymer batteries. These batteries are smaller, flatter, and last much longer than a AAA battery. Attach a single cell LiPo battery, flip the power switch, and you will have a 5V supply to power your LilyPad network. Good up to 150mA. Short circuit protected.

    14,00 €
  10. USB 2 Serial Converter

    Arduinon oma USB-to-serial muunnin. Toimii 5V jännitteellä. Käytä tätä kuten FTDI-kaapelia tai -levyä.

    12,00 €
  11. PoE Module

    The Ag9120-S is a module designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.

    What it means, is that you can power your board (Ethernet Shield, Arduino Ethernet) with cat5-cable.

    18,00 €
  12. Arduino Project Enclosure

    The Arduino enclosure allows you to easily enclose your Arduino main board, Arduino Mega, or some of the other board that fits the Arduino foot print. It simply presses shut, so you don't have to worry about screws or fasteners.

    12,00 €
  13. FTDI Basic Breakout – 3.3V

    FTDI Breakout Board. 3.3V

    16,00 €
  14. LilyPad FTDI Basic Breakout – 5V

    FTDI Breakout Board. Purple and pretty.

    16,00 €
  15. Arduino Stackable Header Kit

    These headers are made to work with the Arduino Main Board, Arduino Pro, and the Arduino Mega. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin and 2 6-pin), enough to connect a shield to an Arduino Main Board.
  16. Arduino Offset Header - 8 Pin

    This is a 8-pin female header, with extra long legs that are slightly offset. The offset helps correct for the weird 0.16" spacing between the two 8-pin headers on the digital side of an Arduino. Stick this and an 8-pin Stackable Header on an Arduino and D7 and D8 pins will be spaced by a more standard 0.2". This allows you to then use a standard perf board stacked on top of the Arduino.

Laskeva

   

16 tuote(tta)