Ostoskorissasi ei ole yhtään tuotetta.

Product was successfully added to your shopping cart.

Akut & Laturit



19 tuote(tta)

  1. Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1

    ‌Tiny charger for 3.7V/4.2V lithium polymer or lithium ion rechargeable batteries.


    7,90 €
  2. Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly charger - v1

    ‌Tiny charger for 3.7V/4.2V lithium polymer or lithium ion rechargeable batteries.

  3. PowerBoost 500 Charger - Rechargeable 5V Lipo USB Boost @ 500mA+

    ‌This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects.

    17,00 €

    ‌A large-sized rechargeable battery pack for your Raspberry Pi or any other USB-powered devices. Two ports, one provides 1A and the other 2A.

    42,00 €
  5. Makeblock Battery Holder 6xAA

    ‌6xAA battery holder

  6. Adafruit LiIon/LiPoly Backpack Add-On for Pro Trinket/ItsyBitsy

    ‌A LiPo battery backpack for Pro Trinket or ItsyBitsy boards.

  7. Polymer Lithium Ion Battery - 110mAh

    This is a very small, extremely light weight battery based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 110mAh!

    7,00 €
  8. Polymer Lithium Ion Battery - 400mAh

    Litium-polymer akku. Kapasiteetti 400 mAh.

    8,00 €
  9. Polymer Lithium Ion Battery - 1000mAh

    Polymer Lithium Ion Battery. 1000 mAh. Great with the Arduino Fio.

    10,00 €
  10. Adafruit Micro Lipo - USB LiIon/LiPoly charger - v1

    Oh so adorable, this is the tiniest little lipo charger, so handy you can keep it any project box! Its also easy to use. Simply plug in the gold plated contacts into any USB port and a 3.7V/4.2V lithium polymer or lithium ion rechargeable battery into the JST plug on the other end. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on. Seriously, it could not get more easy.

  11. LiPo Charger Basic - Micro-USB

    If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work with your battery.

    10,00 €
  12. USB LiPoly Charger - Single Cell

    The USB LiPo Charger is a basic charging circuit that allows you to charge 3.7V LiPo cells at a rate of 500mA or 100mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries.

    14,00 €
  13. LiPower - Boost Converter

    The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection of 2.6V. However, the board can also be used as a general purpose buck and boost regulator with an input voltage as low as 0.3V (default UVLO is 2.6V). With such a low input voltage and quiescent current , the board also works well in energy harvesting applications that use low input voltages.

    15,00 €
  14. LilyPad LiPower

    A small, but very mighty power supply. This board was designed to be as small and inconspicuous as possible. The nice thing about LiPower is the ability to use rechargable Lithium Polymer batteries. These batteries are smaller, flatter, and last much longer than a AAA battery. Attach a single cell LiPo battery, flip the power switch, and you will have a 5V supply to power your LilyPad network. Good up to 150mA. Short circuit protected.

    14,00 €
  15. LilyPad Coin Cell Battery Holder (Switched – 20mm)

    Just like the original Coin Cell Battery Holder, this simple board holds a 20mm coin cell battery (such as a CR2032) and gives you 4 connection points (two positive and two negative) for sewing into your project.

  16. MintyBoost Kit + Tin - v3.0

    The world's first and only open-source hardware charger: The MintyBoost®!

    Make your own iPod/iPhone/GPS/etc... battery-pack and recharger! This project includes all the electronic parts necessary to build your own MintyBoost: a small & simple (but very powerful) USB charger for your iPod (or other mp3 player), camera, cell phone, and any other gadget you can plug into a USB port to charge. Comes with an Altoids Gum sized tin.

    22,00 €


19 tuote(tta)