0Item(s)

Ostoskorissasi ei ole yhtään tuotetta.

Product was successfully added to your shopping cart.

Protoilu

Laskeva

   

Tuotteet 1-20 / 78

  1. 1
  2. 2
  3. 3
  4. 4
  1. Intel® Edison Hardware Pack

    This is a Hardware Pack for the Intel® Edison, with this set you will be provided with increased mechanical strength for stacking Blocks. Each Hardware Pack includes ten M2x3mm standoffs, six M2x3mm screws, and six M2 nuts. With this set of hardware you will be able to secure three Blocks to one Intel® Edison. Eight standoffs and four screws and nuts are used for the Blocks, while two standoffs, screws, and nuts are used for the Intel® Edison itself.

  2. Maker Paste Lead-Free Prototyping Solder Paste

    ‌Lead-Free Prototyping Solder Paste from IC Breakout.

  3. Silicone Cover Stranded-Core Wire - 15m 30AWG Red

    ‌Silicone covered wire. It's soft and flexible.

  4. Silicone Cover Stranded-Core Wire - 15m 30AWG Blue

    ‌Silicone covered wire. It's soft and flexible.

  5. 12.0" JST Male to Male Extension

    ‌‌Use this connector cable with the our gear motors and the connector boards.

  6. 12.0" JST Male to Female Extension

    ‌‌Use this connector cable with the our gear motors and the connector boards.

  7. Adafruit Pi T-Cobbler Plus Kit Breakout for 2x20 Raspberry Pi - RasPi A+, B+, Pi 2, Pi 3, Zero

    ‌‌The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the newer Raspberry Pi computers with a 2x20 connector, that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy.

  8. Female DC Power adapter - 2.1mm jack to screw terminal block

    T‌hese adpaters have a 2.1mm DC jack on one end, and a screw terminal block on the other. 

  9. Short Feather Male Headers - 12-pin and 16-pin Male Header Set

    ‌These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for Featherwings.

  10. Short Feather Headers Kit - 12-pin and 16-pin Female Header Set

    ‌These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather project takes up, but still maintain that flexible configuration

  11. USB 'Noodle' Cable - A/MicroB - 1 meter

    ‌1 meter long flat microUSB cable

  12. Premium Female/Female Jumper Wires - 40 x 3" (75mm)

    ‌Female to female jumper wires. 75 mm long.

  13. Premium Female/Female Jumper Wires - 40 x 6" (150m)

    ‌Female to female jumper wires. 150mm long

  14. Panel Mount USB Cable - A Male to A Female

    ‌‌This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. We think this would be most handy when putting a Beagle Bone, Raspberry Pi or Mintyboost into a box.

  15. Panel Mount Ethernet Extension Cable

    ‌‌This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. We think this would be most useful when putting a Beagle Bone, Raspberry Pi, Arduino Ethernet into a box.

  16. Panel mount HDMI Cable - 40 cm

    ‌‌This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. 

  17. Feather Stacking Headers - 12-pin and 16-pin female headers

    ‌‌A set of two stacking headers meant for the Adafruit Feather boards. 

  18. Adafruit Perma-Proto Half-sized Breadboard PCB - 3 Pack!

    A breadboard shaped prototyping board from Adafruit! Great for transferring your projects from a breadboard to a more permanent PCB.

    12,50 €
  19. Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit

    Adafruit put a PermaProto half sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk.

  20. Ribbon Crimp Connector - 6-pin (2x3, Female)

    These 2x3 crimp connectors can be snapped onto 6-wire ribbon cable to make your own cable assemblies and keep your connections organized. Simply press the connector onto your ribbon cable, no soldering required, which makes it easy to add as many mid-cable connectors as you need.

Laskeva

   

Tuotteet 1-20 / 78

  1. 1
  2. 2
  3. 3
  4. 4