0Item(s)

Ostoskorissasi ei ole yhtään tuotetta.

Product was successfully added to your shopping cart.

Liittimet ja rimat

Laskeva

   

Tuotteet 1-20 / 35

  1. 1
  2. 2
  1. Feather Stacking Headers - 12-pin and 16-pin female headers

    ‌‌A set of two stacking headers meant for the Adafruit Feather boards. 

  2. Panel Mount USB Cable - B Female to Micro-B Male

    ‌Panel mount USB connector (type micro-B to type B)

  3. Male DC Power adapter - 2.1mm plug to screw terminal block

    T‌hese adpaters have a 2.1mm DC plug on one end, and a screw terminal block on the other. 

  4. JST PH 2-pin Extension Cable with On/Off Switch - JST PH2

    ‌JST PH extension cable with on/off switch. Great with Lithium Polymer batteries.

  5. JST PH 2-Pin Cable - Female Connector 100mm

    ‌Your basic JST PH connector wire.

  6. JST PH 2-Pin Cable – Male Header 200mm

    Cable with JST PH male connector

  7. JST SM 2-pin Plug + Receptacle Cable Set

    ‌JST SM connectors. These are the same connectors that are on the Neopixel strips.

  8. Stackable Header - 3 Pin (Female, 0.1")

    ‌This is a simple 3 pin female PTH header. This header is in a configuration that makes it ideal to be used with the MyoWare Muscle Sensor line. Each pin has a spacing of 0.1" in between each other.

  9. Panel Mount USB Cable - B Male to B Female

    ‌Panel mount USB connector (type B to type B)

  10. JST (PH) Jumper 2 Wire Assembly

    Wire with JST (PH) connector and a mating connector.

  11. Short Feather Headers Kit - 12-pin and 16-pin Female Header Set

    ‌These headers are particularly cute and tiny with a body height of just 5.0 mm they are the best way to minimize the amount of space your Feather project takes up, but still maintain that flexible configuration

  12. Short Feather Male Headers - 12-pin and 16-pin Male Header Set

    ‌These headers are particularly cute and tiny and are designed to match perfectly with our shorty female header kit for Featherwings.

  13. Female DC Power adapter - 2.1mm jack to screw terminal block

    T‌hese adpaters have a 2.1mm DC jack on one end, and a screw terminal block on the other. 

  14. Adafruit Pi T-Cobbler Plus Kit Breakout for 2x20 Raspberry Pi - RasPi A+, B+, Pi 2, Pi 3, Zero

    ‌‌The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the newer Raspberry Pi computers with a 2x20 connector, that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy.

  15. Dual Phono Connector for pHAT DAC

    Dual phono connector for the pHAT DAC.

  16. SparkFun Qwiic Shield for Arduino

    ‌A shield for easily connecting sensors that use the Qwiic system to the Arduino.

  17. SparkFun Qwiic Adapter

    ‌‌The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic-enabled board.

  18. Makeblock Me RJ25 Adapter

    ‌RJ25 Adapter for the Makeblock system.

  19. Raspberry Pi - GPIO Shrouded Header (2x13)

    Description: This 2x13 shrouded header has the same number and spacing of pins as the Raspberry Pi so you can easily connect via ribbon cable to the low-level peripherals and get hacking!  This through-hole header has 26 0.1"-spaced pins and is keyed for polarity.

    1,00 €
Laskeva

   

Tuotteet 1-20 / 35

  1. 1
  2. 2